RR-CirKits |
Description |
Picture |
MSRP |
Our
$ |
Part
# |
LCC
Voltmeter and Ammeter. Easily measure your CAN bus power. Size:
1-7/8" x 1-1/8" overall. Dual 4 digit continuous readout.
Red and blue display. Includes a short jumper cable to simplify
insertion anyplace in your existing network. 4-30VDC 10A* maximum.
(* meter only, connectors limited to 1A) |
  |
$20.56 |
$17.48 |
RRK-LCCVAMETER |
Tortoise
Quik-Link The
Tortoise Quik-Link is a plug-and-play control board for Tortoise
slow-motion switch controllers. Breakaway connector inserts allow
use on older Tortoises with narrow paddle contacts.This
board can be directly connected to any LCC I/O output port using
a ribbon cable
OR
Connected via a Quik-Link Breakout board using a 3 wire servo style
cable.Each
Torotise Quik-Link draws about 10mA of power from the LCC CAN Bus.
A powered LCC CAN Bus is required.Feedback
options include Tortoise position or Fascia panel button connection.
Both control and position indication are available over the same
3 wires by using the Button Quik-Link.Tortoise
is a trademark of Circuitron.
|
 |
$17.96 |
$15.27
|
RRK-TORTOISEQL |
Tortoise Quik-Link Package
Tortoise Quik-Link with new style Tortoise included. (green board) |
 |
$35.06 |
$29.80
|
RRK-TORTOISEQLPK |
Tortoise Adapter Board The TAB is designed to provide a
solder-less connection between the SMD-8 and Tortoise. It includes
10 pin daisy chain cable headers and channel selection jumpers.
Breakaway connector inserts allow use on older Tortoises with
narrow paddle contacts. An 8 position screw terminal block allows
easy access to all of the Tortoise connections. LED position indicators
allow easy observation of Tortoise position and power.
Note:
This unit is for use with the SMD-8.
|
IMAGE
COMING SOON! |
$9.61 |
$8.16
|
RRK-TAB |
Tortoise Adapter Board Package of TAB plus Tortoise. |
IMAGE
COMING SOON! |
$28.50 |
$24.23
|
RRK-TABPK |
Tortoise remote Mount This
mounting adapter may be used to mount a Tortoise remotely from the
turnout location. Flexible cable linkage allows installing the remote
actuator above or below the table top and at varying distances and
angles from the Tortoise itself. Linkage adjustments allow for the
various travel distances required by crossing gates or semaphore
signals |
 |
$15.26 |
$12.98
|
RRK-REMOUNT |
Servo Connection Cable (M-M)
This 4" cable may be used to connect two Quik-Link devices. |
 |
$.90 |
$.90
|
RRK-CABSERVMM4 |
Servo Connection Cable (M-M)
This 20" cable may be used to connect two Quik-Link devices. |
 |
$1.80 |
$1.80
|
RRK-CABSERVMM20 |
Servo Extension Cable (M-F) This
39" cable may be used to extend the length of the above (M-M)
cables. |
 |
$2.70 |
$2.70
|
RRK-CABSERVMF39 |
Multiple Terminal
Block Push-in Wiring Cable connector Quick Cable connector, 2 in,
2 out. No more soldering under the layout. Fits AWG 28 - AWG 12
so there is no problem connecting different wire sizes together.
Easily disconnect wiring for trouble shooting or changes. Includes
mounting clip. |
 |
$.90 |
$.90
|
RK-SPL22 |
$19.52 |
$16.59
|
RK-SPL22-25 |
Multiple Terminal
Block Push-in Wiring Cable connector Quick Cable connector, 2 in,
4 out. No more soldering under the layout. Fits AWG 28 - AWG 12
so there is no problem connecting different wire sizes together.
Easily disconnect wiring for trouble shooting or changes. |
 |
$1.02 |
$1.02
|
RK-SPL42 |
$21.36 |
$18.15
|
RK-SPL42-25 |
Multiple Terminal
Block Push-in Wiring Cable connector Quick Cable connector, 2 in,
6 out. No more soldering under the layout. Fits AWG 28 - AWG 12
so there is no problem connecting different wire sizes together.
Easily disconnect wiring for trouble shooting or changes. |
 |
$1.35 |
$1.35
|
RK-SPL62 |
$28.35 |
$24.09
|
RK-SPL62-25 |
I/O
Test Board - Sample Mode The
I/O test board can quickly test the I/O ports on boards such as
the Tower LCC, Mark II, WorkMan series SSB boards, and LCC I/O nodes.This
board has 8 push button switches and 8 LED pairs. It allows simultaneous
input and output tests for each line. |
 |
$8.06 |
$6.85 |
RRK-IOTESTSM |
Isolator
Board - 8 Line This
board provides isolation between 12 Volt DC and the RR-CirKits logic-level
inputs. This allows connection of legacy (12V style) logic and drivers.This
board may be used as a level shifter for voltage conversions in
either direction. (12VDC --> logic levels OR logic levels -->
12VDC) 8 Darlington transistor outputs may be used up to 80V, 50mA.Connect
to other RR-CirKits products usng 10 Pin ribbon cables. |
 |
$22.39 |
$19.03 |
RRK-ISOLATOR8 |
(Opto Isolator - Input Board
- 8 line) This board is normally used for block detection on three
rail layouts. This version of the board includes internal current
limiters. Useful anyplace that an external voltage needs to be monitored.
(5V-20V AC-DC-DCC) |
 |
$24.25 |
$20.62 |
RRK-OIIB8 |
Breakout
Quik-Link This
board allows easy solder-free connections from up to 8 Quik-Link
devices. Converts from 10-pin I/O ribbon cables to 3 wire servo-style
cables. |
 |
$4.46 |
$3.79 |
RRK-BREAKOUTQL |
Button
Quik-Link The
Button-QL is an indicator and push button switch in one package.
This button will snap-fit into a 5/16" diameter hole and requires
2 inches of depth.When
used with an LCC node, the push button switch function and indicator
function may be controlled separately over the same I/O channel.The
built-in LED indicator is configurable using solder jumpers on the
back side. Configuration options include color (Red, Yellow, Green,
OFF) for each position, two brightness levels, and latching/momentary
action.The
button connects via a 3 wire servo-style cable to other Quik-Link
devices. |
 
 
|
$8.96 |
$7.62 |
RRK-BUTTONQL |
Pack
of 8 CT (Current Transformer) coils for RR-CirKits Block Occupancy
Detector (BOD-4/BOD-8). These
100:1 toroid coils sense the track current on leads passing through
the hole in the middle of the coil. Each coil must be connected
to the occupancy detector using "twisted pair" wiring,
such as is found in CAT-5 network cable. |
 |
$14.40 |
$12.24 |
RRK-CTCOILSET8 |
Set of 4 CT (Current Transformer)
coils for BOD4 or BOD4-CP. |
 |
$7.20 |
$6.12 |
RRK-CTCOILSET4 |
Single CT (Current Transformer)
coil. |
 |
$2.25 |
$2.25 |
RRK-CTCOIL |
Block
Occupancy Detector-4 This
board is meant to be used with the RRCirkits Tower LCC or Signal
LCC board via a ribbon cable to create LCC events for LCC train
layout control.The
BOD-4-CP can also be used stand-alone to create digital I/O signals
for block occupancy.This
board operates as a DCC block occupancy detector for up to 4 blocks
using remote CT coils for detection. Detection circuits will output
logic levels, and use the RR-CirKits standard ribbon connector interface.
Each block has a potentiometer sensitivity adjustment.The
CP version also includes two turnout drivers. When used with the
Tower LCC or Signal LCC boards there are also 4 general purpose
I/O connections. These are not available when used with older LocoNet
based devices.The
"Power-Lok" feature preserves the state of block detection
through a track power interruption.
|
 |
$20.97 |
$17.83 |
RRK-BOD4 |
Block
Occupancy Detector-4 This
board is meant to be used with the RRCirkits Tower LCC or Signal
LCC board via a ribbon cable to create LCC events for LCC train
layout control.The
BOD-4-CP can also be used stand-alone to create digital I/O signals
for block occupancy.This
board operates as a DCC block occupancy detector for up to 4 blocks
using remote CT coils for detection. Detection circuits will output
logic levels, and use the RR-CirKits standard ribbon connector interface.
Each block has a potentiometer sensitivity adjustment.The
CP version also includes two turnout drivers. When used with the
Tower LCC or Signal LCC boards there are also 4 general purpose
I/O connections. These are not available when used with older LocoNet
based devices.The
"Power-Lok" feature preserves the state of block detection
through a track power interruption.
|
 |
$27.00 |
$22.95 |
RRK-BOD4CP |
Block
Occupancy Detector - 8 - SM This
board is meant to be used with the RRCirkits Tower LCC or Signal
LCC board via a ribbon cable to create LCC events for LCC train
layout control.The
BOD-8-SM can also be used stand-alone to create digital I/O signals
for block occupancy.This
board operates as a DCC block occupancy detector for up to 8 blocks
using remote CT coils for detection. Detection circuits will output
logic levels, and use the RR-CirKits standard ribbon connector interface.The
"Power-Lok" feature preserves the state of block detection
through a track power interruption.Each
block has a potentiometer sensitivity adjustment.
|
 |
$42.82 |
$36.39 |
RRK-BOD8SM |
Fan
Out Board - Direct Drive The
FOB-A is designed as a simple way to connect a single ribbon cable
to individual wires. Quick-release compression connectors simplify
connection of #18 AWG and smaller wires.The
FOB-A board has two 5-line compression connectors and three 10-pin
headers for ribbon cables. These connection options allow for pass-through
wiring. Each individual output line to the compresson connectors
has a position to mount a resistor for use with LED's.The
wiring on the FOB-A includes two jumper positions to select either
Ground OR Voltage for the "Common" connections on the
compression connectors. |
 |
$13.77 |
$11.70 |
RRK-FOBA |
Fan
Out Board - Dual Direct The
FOB-C is designed as a simple way to connect two flat ribbon cables
to individual wires. Quick-release compression connectors simplify
connection of #18 AWG and smaller wires.The
FOB-C board has two 10-pin headers and four 5-line compression connectors.
Each compression connector has outputs for a "Common"
and 4 of the I/O lines. The wiring on the FOB-C includes two jumper
positions to select either Ground OR Voltage for each of the "Common"
connections. |
 |
$17.73 |
$15.07 |
RRK-FOBC |
BOB-S
(Break Out Board, Screw Terminal) This board is designed to break
out the 10 pin IDC ribbon cables into minature screw terminals for
easy connections. (0.4" wide by 2.5" long) |
 |
$6.26 |
$5.32 |
RRK-BOBS |
Relay
Board - 2 This
product is a Dual 10A DPDT relay board with logic level control.
The RB-2 is suitable for use with the Tower LCC, or other simiar
logic level control devices.A
12V auxiliary power supply is required to power the relay coils.
Auxiliary power is optically isolated from the logic inputs for
double isolation. LED indicators for each relay make it easy to
monitor activity.Includes
dual ribbon connectors to allow pass through connection. Jumper
selection of line 1-8 for each relay. Compatible with LCC Sample
Mode.
|
 |
$28.94 |
$24.60 |
RRK-RB2 |
Relay
Board - 4 This
product is a Quad 10A SPDT relay board with logic level control.
It is suitable for use with Tower LCC and similar logic controllers.This
device requires a 12V auxiliary power supply to power the relay
coils. Auxiliary power is optically isolated from the logic inputs
for double isolation. LED indicators for each relay make it easy
to monitor activity.Includes
dual ribbon connectors with offset lines to allow connection as
output 1-4, or output 5-8 of the Tower LCC or other driver. Now
compatible with LCC Sample Mode.
|
 |
$27.32
|
$23.22 |
RRK-RB4 |
Searchlight
Driver Board This
produce is specifically designed to directly drive 4 four-aspect
signals utilizing bi-polar or three wire LED's. Includes a yellow
color balance control for each of the four signal heads. The 4 LEDs
connect using a single 10-wire ribbon cable. A BOB-S can simplify
connecting the signal masts.Normally
used with Tower LCC.
|
 |
$16.11 |
$13.69 |
RRK-SDB4 |
Dual
Signal Head Driver This
8 output signal head driver is a DCC accessory decoder. Includes
realistic lamp fade and brightness adjustment. Built in resistors
allow direct connections to LEDs. Accepts DCC Signal Aspect messages
or turnout (accessory) commands for control. Compatible with the
Team Digital version. (no longer available from Team Digital)
|
 |
$12.56 |
$10.68 |
RRK-SHD2 |
Stall
Motor Driver This
8 output, low current motor driver is designed for control "stall
motor" switch machines such as the Tortoise® Switch Controllers.
This device can drive up to 100mA per line, with variable speed
regulated output from 6 to 12VDC.Main
Features:
LCC sample mode compatible.
8 individually-controllable outputs
Optically isolated
Low current "H" bridge driver
Up to 100mA per output
Current-limited to 200ma total via PTC fuse |
 |
$33.12 |
$28.15 |
RRK-SMD8 |
(Single Coil Solenoid Driver)
This 8 line, optically isolated, single ended, high current, high
voltage DC driver can drive up to 1A continous per line at up to
30VDC. When used with custom Tower LCC settings and a CD power supply
this board will drive 4 dual-coil solenoid switch machines. (PTC
fuse limited to 2-3A total per board for safety) |
 |
$35.98 |
$30.58 |
RRK-SCSD8 |
SSSB style 4 circuit pogo-pin
break away magnetic signal mount. Use with 3/32" mast or with
SSSB-MB decoder/drivers. (see below) Includes 3-1/2" M-F pigtails.
Top portion 10mm square. Screw down base 28 mm L x 10mm W. Magnet
14mm OD. |
 |
$13.50 |
$11.48 |
RRK-SSSBMAGBASE |
Common Anode five head Decoder/Driver
strip fits signal bridges with multiple heads. (splice or cut to
length for required number of heads) 6 mm x 12mm per head. |
 |
$13.50 |
$11.48 |
RRK-SSSB-BRCA5 |
Single head Common Anode Decoder/Driver
for Atlas Micro JST equipped HO signals. Includes 3-1/2" M-F
pigtails. |
 |
$6.30 |
$5.36 |
RRK-SSSBATL-SINGLECA |
Atlas Single
Single head Common Cathode Decoder/Driver for Atlas Micro JST equipped
N or O signals. Includes 3-1/2" M-F pigtails. |
 |
$8.10 |
$6.89 |
RRK-SSSBATL-SINGLECC |
Dual head Common Anode Decoder/Driver
for Atlas Micro JST equipped HO signals. Includes 3-1/2" M-F
pigtails. |
 |
$8.10 |
$6.89 |
RRK-SSSBATL-SINGLECC |
Dual head Common Anode Decoder/Driver
for Atlas Micro JST equipped HO signals. Includes 3-1/2" M-F
pigtails. |
 |
$9.90 |
$8.41 |
RRK-SSSBATL-DUALCC |
Dual head Decoder/Driver for
10 pin header equipped signals. Includes 3-1/2" M-F pigtails. |
 |
$9.90 |
$8.41 |
RRK-SSSBDIG-DUAL |
SSSB-Dwarf
Single head Decoder/Driver for Showcase Miniatures Type SA. (SKU:
2194) Includes 3 color LED. (decoder/driver only, Showcase Miniatures
signal hardware detail not included) Includes 3-1/2" M-F pigtails. |
 |
$9.00 |
$7.65 |
RRK-SSSB-DWARFSIG |
Single head Decoder/Driver with
screw terminals for wire equipped signals. Includes 3-1/2"
M-F pigtails. |
 |
$6.75 |
$5.74 |
RRK-SSSB-S-SINGLE |
Dual head Decoder/Driver with
screw terminals for wire equipped signals. Includes 3-1/2"
M-F pigtails. |
 |
$9.00 |
$7.65 |
RRK-SSSB-S-DUAL |
The SSB Adapter ties together
2 LocoNet jacks, one Simple Serial Bus terminal, and a power supply.
The SSB Adapter is for use with an existing LocoNet® when used
on a Digitrax DCC system or to extend a stand alone LocoNet®.
It provides an easy way to connect to, or to add additional power
to the SSB. PS-S-15-700 universal switching power supply and 5'
LocoNet® compatible cable are included. |
 |
$17.96 |
$15.27
|
RRK-SSB-ADAPTER |
The SSB Gateway ties together
4 LocoNet jacks, two Simple Serial Bus plugs, and a power supply.
The SSB Gateway optionally supplies the required LocoNet® 15ma.
pull up and DC power to the RailSync lines for a stand alone LocoNet®
when used on DCC systems other than Digitrax. It provides an easy
point to connect a LocoBuffer-USB to interface the SSB to a computer.
PS-S-15-1500 universal switching power supply and 5' LocoNet®
compatible cable are included. |
 |
$32.36 |
$27.51
|
RRK-SSB-GATEWAY |
Signal
LCC-P 16
Led drivers plus 8 line Input/Output node for NMRA CAN bus LCC®Logic
level I/O port compatible with other standard RR-CirKits I/O modules.The
"P" version of the Signal LCC uses pin headers to connect
wires and corresponding connectors to and from your switch controllers.Main
Features:
Small package size: 1-3/4" x 3-1/4" x 5/8"
Dual 10 pin headers for LED connections
Bootloader for in-the-field firmware upgrades
Includes powerful internal Logic Elements
Compatible with JMRI
POC (Powered Over CAN) LCC® connections*
*Note: Requires a powered LCC bus. [20 ma. bus load] (plus any I/O
load current such as LEDs) |
 |
$66.56 |
$56.57 |
RRK-SIGNALLCCP |
Signal
LCC-S 16
Led drivers plus 8 line Input/Output node for NMRA CAN bus LCC®Logic
level I/O port compatible with other RR-CirKits I/O modules.The
"S" version of the Signal LCC uses screw terminals to
connect wires to and from your switch controllers.Main
Features:
Small package size. Just 1-3/4" x 3-1/4" x 5/8"
Miniture Screw Terminals for LED connections.
Bootloader for in-the-field firmware upgrades.
Includes powerful internal Logic Elements.
Compatible with JMRI.
POC (Powered Over CAN) LCC® connections*
*Note: Requires a powered LCC bus. [20 ma. bus load] (plus any I/O
load current such as LEDs) |
 |
$66.56 |
$56.57 |
RRK-SIGNALLCCS |
Signal
LCC-32H 32
Head signal controller plus 8 line Input/Output node for LCC®.(maximum
of 96 lamps) Compatible with JMRI for signal logic.Requires
SSSB (Simple Serial Signal Bus) decoder/drivers at each signal head.Main
Features:
Small package size. Just 1-¾" x 3-1/4" x 5/8"
POC (Powered Over CAN) LCC® connections*
*Note: Requires a powered LCC bus. [20 ma. bus load] (plus any I/O
load current such as LEDs)
Uses Futaba J (polarized 3 wire) Servo extension cables between
signal heads. |
 |
$86.36 |
$73.41 |
RRK-SIGNALLCC32H |
16 Line Input/Output node for NMRA CAN bus LCC®. Logic level
interface compatible with other standard RR-CirKits I/O modules.
Boot Loader for user install able firmware upgrades. Includes powerful
internal Logic Elements. Also compatible with JMRI. Small package
size. Just 1-¾" x 3-1/4" x 5/8". POC (Powered
Over CAN) LCC® connections*. *Note: Requires a powered LCC bus.
[20 ma. bus load] (plus any I/O load current such as LEDs) |
 |
$62.96 |
$53.51 |
RRK-TOWERLCC |
The SignalMan-C (Compression
Connectors) communicates over the LocoNet® compatible Simple
Serial Bus to other LocoNet® compatible devices and operates
with layout control software such as JMRI and RR&Co. via the
LocoBuffer-USB, or else it connects directly to the DCC bus as an
accessory decoder. Compression connectors included. |
 |
$37.12 |
$31.55 |
RRK-SIGNALMANC |
The SignalMan-P (Pin Connectors
or IDC Plug) communicates over the LocoNet® compatible Simple
Serial Bus to other LocoNet® compatible devices and operates
with layout control software such as JMRI and RR&Co. via the
LocoBuffer-USB, or else it connects directly to the DCC bus as an
accessory decoder. Female pin connectors and shrink wrap included. |
 |
$31.43 |
$26.72
|
RRK-SIGNALMANP |
The SignalMan-S (Screw Terminals)
communicates over the LocoNet® compatible Simple Serial Bus
to other LocoNet® compatible devices and operates with layout
control software such as JMRI and RR&Co. via the LocoBuffer-USB,
or else it connects directly to the DCC bus as an accessory decoder. |
 |
$37.42 |
$31.80
|
RRK-SIGNALMANS |
Tower
LCC+Q This
product is a 16-Line Input/Output node for NMRA CAN Bus LCC®Built-in
PLC-style text-based Logic Engine. Logic-level interface is compatible
with other RR-CirKits I/O modules such as the Signal LCC, RB-4,
etc.Main
Features:
Small package size: 1-3/4" x 3-1/4" x 5/8"
Bootloader for in-the-field firmware upgrades.
+Q version includes a new more powerful internal Logic Engine compared
to earlier versions of the Tower LCC.
Compatible with JMRI for graphical configuration
POC (Powered Over CAN) LCC® connections*.
*Note: Requires a powered LCC bus. [20 ma. bus load] (plus any I/O
load current such as LEDs) |
 |
$62.96 |
$53.51 |
RRK-TOWERLCCQ |
TC Mark II (Tower Controller
Mark II) 64 line I/O controller, configured as 64 I/O lines. Each
line may drive up to 15ma. at 4.5V when configured as an output
and is equipped with 4.7K pull up resistors to allow use with contacts,
open collector, or logic level circuits when configured as an input.
Includes connectors and LocoNet® cable. |
 |
$120.94 |
$102.80 |
RRK-TCMARKII |
LCC-LocoNet
Gateway This
product can be used to connect devices between the LCC® CAN
Bus and the Digitrax LocoNet. The LCC-LocoNet Gateway is an ideal
starting point for Digitrax users with the desire to add LCC to
their layout. It may also be used to add existing Digitrax throttles
and other hardware to LCC layouts, such as one powered by a CS-105.The
USB interface to a computer is not required when using a CS-105
WiFi connection!15VDC
1.5Amp power supply and CAN Bus terminators included!Main
Product Features:
Small package size: 2-7/16" x 4-3/8" x 1-1/8". (including
mounting flanges)
Bi-directional conversion (LCC <-> LocoNet) of messages for
Turnouts, Sensors, and Signals.
Dual RJ45 connectors for LCC ® CAN Bus connections.
Dual RJ12 connectors for the LocoNet. (stand alone LocoNet optional)
Includes USB Type B connector to connect a PC. Works with JMRI over
LCC/OpenLCB protocol.
600 ma power supplied to each LCC® CAN Bus port |
 |
$134.96 |
$114.72 |
RRK-LCCLOCONETGW |
Power-Point
LCC Power-Point ties together 2 LCC jacks, a Traffic Monitor, and
a power supply. Create a powered LCC bus for simple wiring by powering
your LCC Nodes over the cable. The LCC Power-Point supplies 1/2A
to each LCC CAN Bus cable. PS-S-15-1500 universal switching power
supply is included. (Terminator and CAN bus cable shown are not
included) Additional Power-Point units may be added as required
by your system's power requirements. |
 |
$26.96 |
$22.92 |
RRK-LCCPOWERPOINT
|
LCC-Terminator
NMRA CAN bus LCC® Termination Pair. May be used to provide
the required termination at each end of the CAN bus LCC® Balanced
CAN termination provides the best noise rejection. Includes CAN
bus Power Indicator and CAN bus data monitor for easy network
cable trouble shooting. LCC requires two terminators per bus segment.
|
  |
$13.50 |
$11.48 |
RRK-LCCTERMINATORPR |
NMRA CAN bus
LCC® to USB interface This
product can be used to interface your wired LCC network with a
computer. Simplify your LCC configuration process, use a PC-based
CTC, and more! Compatible with JMRI. Ready to run. USB cable included.
No add-on power supply required!
No jumpers or switches to set!
No additional purchases required!The
LCC-USB can be used to update firmware on wired LCC products,
including the TCS LT-50 and B-106.NOTE:
This product is NOT the LCC-Loconet gateway for Digitrax products.Main
Features of This Product:
Small package size - Just 1-1/2" x 2-1/4" x 3/4"
Digital isolation between CAN bus LCC® and USB port
USB Type B connector for PC
Dual RJ45 connector for LCC® CAN Bus connections
Four Status LEDs (Ready, Power, Transmit, and Receive)
High speed data: 125,000 baud rate over LCC® CAN Bus
Buffered inputs and outputs for high speed, error free data transmission.
Powered directly from LCC* and USB port.
*Note: Requires a powered LCC bus. [10 ma. bus load]
Note:
This unit is NOT for the Digitrax LocoNet
(See Digitrax LocoNet Below)
|
 |
$62.96 |
$53.52 |
RRK-LCCBUFFERUSB |
LCC Starter Kit Introductory
price for a LCC Buffer-USB, a Power-Point, 2 Terminators, includes
1' LCC cable and USB cable. |
   |
$89.96 |
$76.47 |
RRK-LCCSTARTERKIT
|
LocoBuffer-NG (Next Generation)
Digitrax LocoNet® to USB type-A* Interface unit. 1,500 Volt
Digital isolation between LocoNet and USB port. Type A* USB connector
for direct computer connection. RJ12 connector for LocoNet connection.
3 status LEDs. (G-LocoNet Power, R-Activity, and Y-USB enumerated)
Small package size 2" x 1" x 5/8". Plug and play
with latest Linux, Mac, and Windows systems. Includes LocoNet cable.
*Powered directly from LocoNet bus and USB port. *Notes: Uses RailSync
power. [10 ma. RailSync load] May require a USB Type C Male to USB
Type A Female adapter cable for some systems. |
 |
$54.43 |
$46.27 |
RRK-LBNG
|
LCC
Repeater This
Bit-level repeater connects two LCC® CAN Bus segments and boosts
the signal from one side to the other. This device is only required
on layouts with long runs between nodes with long sections of CAN
Bus cable where the signal level can attentuate. 15VDC
1.5 Amp power supply included!Main
Features:
Small package size. Just 2-1/2" x 3-1/2" x 1". (including
mounting flanges)
Quad RJ45 connectors for dual LCC® CAN Bus loop through connections.
Includes a CAN bus data monitor LED for network trouble shooting.
2 LED display.
600 ma power supplied to each LCC® CAN Bus segment. |
 |
$58.46 |
$45.52 |
RRK-LCCREPEATER |
(Single Position Mounting Track) This plastic mounting track
is suitable for mounting a single I/O module to a flat surface.
(3 1/2" x 2")
(I/O board not included)
|
 |
$2.61 |
$2.61 |
RRK-3TK2-1 |
(Dual Position Mounting Track) This plastic mounting track is
suitable for mounting two I/O modules to a flat surface. (3 1/2"
x 4")
(I/O board not included)
|
 |
$5.22 |
$4.45 |
RRK-3TK2-2 |
(Single Position Mounting Track) This plastic mounting track
is suitable for mounting a single I/O module to a flat surface.
(3 1/2" x 2")
(I/O board not included)
|
IMAGE
COMING SOON! |
$6.53 |
$5.55 |
RRK-3TK2-2W |
(Single Position Mounting Track) This plastic mounting track
is suitable for mounting a single I/O module to a flat surface.
(3 1/2" x 2")
(I/O board not included)
|
IMAGE
COMING SOON! |
$7.83 |
$6.66 |
RRK-3TK2-3 |
(Single Position Mounting Track) This plastic mounting track
is suitable for mounting a single I/O module to a flat surface.
(3 1/2" x 2")
(I/O board not included)
|
IMAGE
COMING SOON! |
$10.44 |
$8.88 |
RRK-3TK2-3W |
(Single Position Mounting Track) This plastic mounting track
is suitable for mounting a single I/O module to a flat surface.
(3 1/2" x 2")
(I/O board not included)
|
 |
$10.44 |
$8.88 |
RRK-3TK2-4 |
(Single Position Mounting Track) This plastic mounting track
is suitable for mounting a single I/O module to a flat surface.
(3 1/2" x 2")
(I/O board not included)
|
 |
$14.36 |
$12.21 |
RRK-3TK2-4W |
(Single Position Mounting Track) This plastic mounting track
is suitable for mounting a single I/O module to a flat surface.
(3 1/2" x 2")
(I/O board not included)
|
IMAGE
COMING SOON! |
$15.66 |
$13.32 |
RRK-3TK2-6 |
(10 conductor flat ribbon interface cable) 100' rolls, #28 AWG
gray with red stripe on line one. Used to connect any daughter
cards to the Tower Controller, TowerMan, or LNCP boards. Also
used to connect signals to the 4ASD-4 board, LNCP, SignalMan-P,
or to the Tower Controller. Cable is heavy and will incur extra
cost for shipping.
|
 |
$44.96 |
$38.21 |
RRK-CAB-10X100 |
(10 position IDC socket) Box of 25 Insulation Displacement Connectors
for use with 10 wire flat ribbon cable.
|
 |
$7.16 |
$6.09 |
RRK-IDC-S10X25 |
(10 position IDC male) Box of 10 Male Insulation Displacement
Connectors for use with 10 wire flat ribbon cable. Use with IDC-S10
to create extension cables. Screw ears allow easy mounting to
the layout
|
 |
$10.67 |
$9.07 |
RRK-IDC-M10X10 |
(10 position IDC male with latch) Box of 10 Insulation Displacement
Connectors for use with 10 wire flat ribbon cable. Use with IDC-S10
to create extension cables. Screw ears allow easy mounting to
the layout.
|
 |
$11.57 |
$9.85 |
RRK-IDCM10LATCHX10 |
15V DC Power Adapter (1500mA Output, 100-240V AC Input, 2.1mm
ID / 5.5mm OD)
This high quality regulated switching power adapter powers any
15 Volt DC device up to 1.5 Amp. Made with quality in mind, this
unit outperforms similar products. Let RR-CirKits keep your devices
powered on and working great with our professional grade power
supplies. This constant power output supply is designed to start
up reliably even under large capacitive loads.
|
 |
$10.80 |
$9.18 |
RRK-PSS-15-1500 |
SS-RGY-24 This RGY LED is provided with four 24" long color
coded #36 AWG wires. It may be fitted in place of a common T-1
LED with room to spare. The LED provides the three standard searchlight
signal colors and is wired the same as a normal three light signal
head would be. (common anode connection)
|
 |
$4.28 |
$4.28 |
RRK-SS-RGY-24 |